DIY: Bathroom Vanity

Turn an outdated dresser in to a one-of-a-kind bathing room vanity.

There are two sorts of basins (sinks): bathing room basins, which suit 1-1/4” drains; and bar basins, which suit 1-1/2” drains. Most bathing room faucets incorporate a 1-1/4” pop-up drain assembly. Depending concerning the sink you choose, you could possibly need to purchase a separate drain assembly. Be good your sink and faucet arranged are compatible.

When searching for a wooden cupboard or dresser to convert in to a vanity, spend near curiosity in the direction of the dimensions inside the cabinet. Ideally, purchase your sink major to make certain that you just can choose a cupboard using the correct dimensions – some thing that is broad and deep adequate to accommodate the sink, leaving space in the back again inside the cupboard to suit a faucet arranged at the same time to space in the entrance inside the cupboard to make certain the fact that sink does not work up in the direction of the entrance edge. The cupboard need to be also roughly 32” huge – normal vanity height.

If you are converting a cupboard with shelves and even a dresser, you will possibly need to minimize by method of the back again and bottom inside the shelves or drawers to accommodate plumbing related components and pipe. this could make the drawers somewhat unstable, which means you could possibly should fix the best drawer permanently in area by screwing it in the direction of the frame inside the cupboard from beneath, filling the screw holes and touching them up with paint or stain. for individuals who truly desire to create utilization of the drawers which have components minimize away from them, consider lining them with plastic material baskets so scaled-down products do not fall out the back again or bottom.

Materials and Tools
•Cardboard
•Sink
•Pencil and ruler
•Sharp energy knife
•Masking tape
•Electric drill with 1” drill bit
•Jigsaw
•Faucet set
•Wrench
•Paintbrush, or roller and tray
•Varathane
•Water provide lines
•Drain assembly
•Chrome P trap (may be supplied using the sink)
•2-1/2” hole saw*
Step 1: Make sink hole template
Many sinks occur with templates to help information you in slicing the hole all through the vanity top. If your sink does not occur using a template, make one your do it yourself from cardboard. arranged the sink upside right down over a product of cardboard and trace near to the lip inside the sink onto the cardboard using a pencil. (See Photo 2) this could in all likelihood be the theme for slicing the sink hole all through the best inside the cabinet.

Step 2: minimize sink hole
With masking tape, securely tape the cardboard theme in the direction of the greatest inside the cupboard all through the area especially where you’d such as the sink getting situated. using a 1” drill bit, drill a hole in to the cabinet, just inside the cardboard template. This hole will enable one to acquire the jigsaw started. using a jigsaw, minimize the sink hole, subsequent the hole all through the cardboard theme when you go.
Step 3: Drill faucet holes
To determine the faucet placement, reduce the sink in to the minimize sink hole – you can appraise by eyesight probably the most useful area to the faucet. get rid of the sink. center the faucet arranged concerning the cupboard just at the rear of especially where the sink will sit. Mark the area with masking tape. using a pencil, mark the tape using the area inside the faucet spout as well as the 4” centre-to-centre tap measurement (i.e. 2” to both facet inside the faucet spout). Drill the holes to the faucets at those people factors 4” apart utilizing a 1” drill bit.

Step 4: Varathane vanity top
With a paintbrush, or roller and tray, take advantage of numerous protective coats of obvious Varathane in the direction of the greatest inside the vanity. Be good to Varathane the minimize borders inside the sink hole as well; this could seal the wooden and give protection to it from consuming water seepage and wetness. allow Varathane to dried out completely preceding to proceeding.

Step 5: minimize holes in cupboard back
To determine the placement inside the drain pipe and consuming water provide shut-offs concerning the back again inside the cabinet, assess their spots concerning the wall and shift these spots in the direction of the back again inside the cabinet. utilizing a 2-1/2” hole saw, minimize holes all through the back again inside the cupboard to accommodate the drain pipe as well as the consuming water provide shut-offs. (The holes should be huge adequate to obvious the handles inside the shut-offs.) set up cupboard versus wall.

Step 6: Attach faucet
Turn away the consuming water provide shut-offs. reduce all through the faucet arranged and tighten it into area from underneath. The faucet arranged will occur with each of the essential components (i.e. washers, rubber rings, etc; see our components image for assembly parts). With faucet arranged firmly in place, attach the consuming water provide lines. Connect these in the direction of the consuming water provide shut-offs coming out inside the wall, and tighten. (See Photo 6)

Step 7: set up drain assembly and sink

Depending concerning the sink you use, the drain assembly components will in all likelihood be 1-1/4” or 1-1/2”. We employed a bar sink, which essential a 1-1/2” drain assembly. (Bathroom sinks will need a 1-1/4” pop-up assembly, which need to occur using a bathing room faucet set.) arranged the drain in to the sink, attach the rubber washer and nut onto the drain under the sink, and tighten. Screw concerning the tail piece. reduce the sink in to the sink hole. Our sink experienced clips to sustain it into place.

Step 8: Attach P trap

Attach the P trap onto the tail product and in the direction of the trap adaptor coming out inside the wall. (See Photo 8) The drain assembly will determine the sizing inside the P trap (i.e. both 1-1/2” or 1-1/4”). Turn concerning the consuming water provide shut-offs.

Step 9: Modify dresser drawers
Measure and mark concerning the drawers away from your back again inside the cupboard in the direction of the entrance phase inside the P trap. As well, mark the spots as well as the widths inside the consuming water shut-offs; the drawer will should obvious these too. using a jigsaw, minimize out the back again and bottom inside the drawers based on these measurements to make certain the fact that drawers can now adequately obvious all plumbing related parts, consuming water shut-offs and adaptor. (See Photo 9) Slide the drawers back again into place. (See Photo 10).

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>